-
1 air duct of rectangular cross-section
короб вентиляционный 1)
Воздуховод прямоугольного (коробчатого) сечения, применяемый в системе вентиляции и кондиционирования воздуха
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]1) Устаревший термин
[Интент]
Прямоугольный воздуховод
[http://www.normal-vent.ru/materiali_izgotovleniya_vozduhovodov.shtml]Тематики
Синонимы
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > air duct of rectangular cross-section
-
2 air duct
воздуховод
Замкнутый по периметру канал, предназначенный для перемещения воздуха или смеси воздуха с примесями под действием разности давлений на концах канала.
Примечание. По форме поперечного сечения воздуховод может быть прямоугольным или круглым.
[ ГОСТ 22270-76]
воздуховод
Трубопровод для принудительного перемещения воздуха в технических целях
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
воздухопровод
Трубопровод для подачи воздуха к металлургич. агрегатам, конструкция к-рого зависит от назнач. Напр., в. для подвода воздушного дутья к фурмам домен. печи выполняется в виде опоясыв. стальной трубы с внутр. диаметром < 1400 мм, футеров. изнутри огнеупорным кирпичом.
[ http://metaltrade.ru/abc/a.htm]Тематики
EN
воздушный канал
вентиляционный канал
воздухопровод
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
Синонимы
EN
короб вентиляционный 1)
Воздуховод прямоугольного (коробчатого) сечения, применяемый в системе вентиляции и кондиционирования воздуха
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]1) Устаревший термин
[Интент]
Прямоугольный воздуховод
[http://www.normal-vent.ru/materiali_izgotovleniya_vozduhovodov.shtml]Тематики
Синонимы
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > air duct
-
3 air channel
воздуховод
Замкнутый по периметру канал, предназначенный для перемещения воздуха или смеси воздуха с примесями под действием разности давлений на концах канала.
Примечание. По форме поперечного сечения воздуховод может быть прямоугольным или круглым.
[ ГОСТ 22270-76]
воздуховод
Трубопровод для принудительного перемещения воздуха в технических целях
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
канал вентиляционный
Воздуховод в системе вентиляции, устраиваемый в толще конструкций или в подвесных наружных коробах
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
короб вентиляционный 1)
Воздуховод прямоугольного (коробчатого) сечения, применяемый в системе вентиляции и кондиционирования воздуха
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]1) Устаревший термин
[Интент]
Прямоугольный воздуховод
[http://www.normal-vent.ru/materiali_izgotovleniya_vozduhovodov.shtml]Тематики
Синонимы
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > air channel
-
4 disc type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc type winding
-
5 disc winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc winding
-
6 disk type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disk type winding
-
7 disk winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
дисковая обмотка
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > disk winding
См. также в других словарях:
Duct (HVAC) — A round galvanized steel duct connecting to a typical diffuser Fire resistance rated … Wikipedia
Lion of Babylon — A fully equipped Asad Babil on display at Fort Hood Type Main battle tank Place of … Wikipedia
building construction — Techniques and industry involved in the assembly and erection of structures. Early humans built primarily for shelter, using simple methods. Building materials came from the land, and fabrication was dictated by the limits of the materials and… … Universalium
Marstonia comalensis — Shell of one of the lectotypes of Marstonia comalensis. Scale bar is 1.0 mm. Scientific classification Kingdom … Wikipedia
Kaval — This article is about the flute. For the city in Iran, see Kavar. For the professional wrestler formerly known as Kaval, see Low Ki. Kaval Bulgarian kaval in C (До) made in 2009 from European Cornel (Cornus mas) Дрян Classification … Wikipedia
digestive system, human — Introduction the system used in the human body for the process of digestion. The human digestive system consists primarily of the digestive tract (alimentary canal), or the series of structures and organs through which food and liquids pass… … Universalium
Central Asian arts — Literary, performing, and visual arts of Afghanistan, Azerbaijan, Kazakhstan, Kyrgyzstan, Mongolia, Nepal, Tibet, Turkmenistan, Uzbekistan, and parts of China and Russia. The term usually denotes only those traditions not influenced by the… … Universalium
ear, human — ▪ anatomy Introduction organ of hearing and equilibrium that detects and analyzes noises by transduction (or the conversion of sound waves into electrochemical impulses) and maintains the sense of balance (equilibrium). The human ear, like … Universalium
Electrical wiring — in general refers to insulated conductors used to carry electricity, and associated devices. This article describes general aspects of electrical wiring as used to provide power in buildings and structures, commonly referred to as building wiring … Wikipedia
Waveguide — This page is about waveguides in the most general sense. For ordinary metal pipe waveguides, Waveguide (electromagnetism). For optical waveguides, see Waveguide (optics). A section of flexible waveguide with a pressurizable flange … Wikipedia
wind instrument — /wind/ a musical instrument sounded by the breath or other air current, as the trumpet, trombone, clarinet, or flute. [1575 85] * * * ▪ music Introduction any musical instrument that uses air as the primary vibrating medium for the… … Universalium
